How To Replace A Gas Dryer Belt

The video below shows how to replace a broken drive belt in a gas dryer, but the repair steps are the same for electric dryers. This repair procedure covers kenmore, whirlpool, maytag, amana, roper, crosley and estate dryers with a lint screen housing located in the top cabinet panel.

GE Dryer Repair How to replace the Drive Belt Dryer

Remove the braces and disconnect the sensor wires.

How to replace a gas dryer belt. Pull the belt off of the dryer drum and install the new one, ribbed side down. First unplug the dryer power cord. The simplest way to replace the belt is as follows (which took me hours to figure out).

All of the information for this drive belt replacement video is applicable to the following brands: Next, take a putty knife and slide it in to the small opening between the top of the dryer and the front of the dryer. You will have to reach back into the dryer cabinet below the drum to locate and release the old belt if it is still attached to the motor pulley.

The average gas dryer is a little less durable, lasting about 13 years. If you’re trying to determine whether to repair or replace your dryer, a good rule of thumb is to know the lifespan of your appliance. The most common reasons for replacing the drive belt are when the dryer makes noise, won’t start, or won’t turn at all.

Most of the dryers require a grooved type belt. Now slide the new belt over the drum. Push down on the tension pulley and loop the belt around it.

Remove the screws of the dryer top panel and remove the panel. If you spent $1,200 on a bosch dryer three years ago, and repairs are minimal, it’s probably best to hold onto your current dryer for a few more years. Before you replace the dryer drive belt be sure to unplug the power cord.

Fit your new belt through the tensioner and around the pulley on the motor, making sure the traction grooves are facing the pulley in the correct fashion. Pull the broken belt out of the cabinet. Replace the back on the dryer and install the retaining screws with the screwdriver.

Pull the loop through the idler arm and connect the other end to the motor pulley. This will reveal two screws, which need to be removed in order to get the top of the dryer off. After removing the front panel, you should be able to remove the old belt.

Slide the new belt over the drum. Using both hands under the tumbler, route the belt around the motor pulley and idler pulley. There were no instructions to follow until i realized i.

Then, it’s possible to remove the old belt, vacuum the debris and then replace it with the new belt. If the dryer is past its life expectancy, it may be cheaper to replace it versus to try to repair it. Note the life expectancy of your dryer.

To accomplish this, you have to remove the lint filter and dryer top and remove the screws holding on the front of the dyer. Thread the drive belt through the idler pulley. Slide the old belt to the front of the drum and then remove it.

Slide the new belt over the rear of the tumbler with the ribbed side pointed to the inside. You need to disconnect the door switch before you remove the front panel. Lay down in front of the dryer, and look underneath the drum to the belt tensioner and the electric motor that turns the drum.

Push the idler pulley to the right and loop the drive belt over the motor pulley. Loop the new belt around the drum and the motor pulley. Lift the front of the drum to access the drive motor and idler pulley.

Pull the panel out from the bottom to detach. This all depends, of course, on how often the dryer is run and how often it’s had regular maintenance, as. Remove the old belt and move the replacement belt into the belt track on the drum.

Grasp the belt at the bottom of the drum and form a loop. Hi renofab, to replace the belt on your dryer : When a squeaking noise is heard, it’s likely that the dryer belt needs to be replaced.

Use a 5/16th inch socket or nut driver to unthread the screws securing the lower access panel. Pull the idler pulley to the left while routing the belt, and carefully allow the idler pulley back to the right to apply tension. The motor is behind the blower and will be hard to get to.

Position the new drive belt on the dryer drum. Move the idler pulley to the right and thread the belt through the center of it. Internal metal edges in the dryer can be sharp.

I figured the problem was the drive belt so i ordered a new one. Pull the front panel off of the dryer and set it aside. The average electric dryer should last about 14 years.

Manually rotate the drum to ensure proper tension is on the belt and the looping sequence is. General electric gas dryer ddg5380gdl my repair & advice featured story. The first step in replacing a dryer belt is to slide out the lint filter.

Depress the pulley which will remove the tension of the old belt. Some of the dryers will come with a bulkhead that supports the front panel. The belt will be a bit too large for the drum until threaded through the motor at the bottom right of the dryer.

Next, unthread the screws securing the bottom of the front panel. Next remove the filter and two screws that are located under the filter, go to front of dryer and there will be two clips under the lid about two inches from each side, use a flat blade like a putty knife and press inwards on each clip while lifting the top, repeat opposite side.

Dryer Belt (part 40111201) How To Replace (With images